Concrete Patio & Driveway Cost in Tennessee (2026)
Concrete Patio & Driveway in Tennessee runs about 8% below the national average. A typical 600 sq ft project starts around $3,310–$6,620 for standard broom finish. Estimate your exact project below.
Tennessee runs below the national average on cost, though rapid growth around Nashville has tightened its labor market and pushed some prices upward.
Reviewed by the AnyCoster Research Team · How we estimate costs
Concrete Patio & Driveway Cost Calculator
Adjust the details for an installed-cost range tailored to you.
Length × width of the slab. A 2-car driveway is ~600 sq ft.
Ballpark estimate for planning — not a quote.
Get your exact price from local concrete pros
This is a ballpark — compare up to 3 free, no-obligation quotes from vetted contractors in Tennessee.
Concrete Patio & Driveway cost in Tennessee by material
Installed cost for a typical 600 sq ft project in Tennessee.
| Material | Per sq ft | Typical TN project |
|---|---|---|
| Standard broom finish | $5.5–$11.0 | $3,310 – $6,620 |
| Stamped / colored | $11.0–$18.4 | $6,620 – $11,040 |
| Paver equivalent | $13.8–$25.8 | $8,280 – $15,460 |
What affects your Tennessee cost
- Finish (plain vs stamped/colored)
- Slab thickness and rebar/mesh reinforcement
- Site prep, grading and old-slab removal
- Access for the concrete truck
- Local labor and material prices
Concrete Patio & Driveway in Tennessee: local factors that move the price
Climate & weather
Humid summers, mild-to-cold winters, and heavy rainfall bring moisture and occasional flooding, while the state's storm exposure makes wind resistance relevant. Good drainage and mildew-resistant finishes help.
Regional norms in Tennessee
Brick and vinyl siding with pitched roofs are common across the state.
Best time to schedule
Fall and spring offer the most comfortable conditions for exterior work.
Permits & code
Most Tennessee jurisdictions require permits for structural and electrical work, with requirements varying between cities and rural counties.
Tennessee concrete patio & driveway — FAQ
How much does concrete patio & driveway cost in Tennessee?
In Tennessee, a typical 600 sq ft concrete patio & driveway project runs about $3,310–$6,620 for standard broom finish, installed. That's about 8% below the national average. Higher-end materials cost more — use the calculator above for your exact size and material.
How much does concrete patio & driveway cost per sq ft in Tennessee?
In Tennessee, installed concrete runs about $5.5–$25.8 per sq ft depending on material (standard broom finish $5.5–$11.0, stamped / colored $11.0–$18.4, paver equivalent $13.8–$25.8). That's about 8% below the national average.
Do I need a permit for concrete patio & driveway in Tennessee?
Most Tennessee jurisdictions require permits for structural and electrical work, with requirements varying between cities and rural counties. Always confirm requirements with your local building department, and factor permit time and inspections into your schedule.
When is the best time to do concrete patio & driveway in Tennessee?
Fall and spring offer the most comfortable conditions for exterior work. Humid summers, mild-to-cold winters, and heavy rainfall bring moisture and occasional flooding, while the state's storm exposure makes wind resistance relevant. Good drainage and mildew-resistant finishes help.
How much does a concrete driveway cost in 2026?
A standard ~600 sq ft concrete driveway runs about $3,600–$7,200 installed; stamped or colored concrete runs $7,200–$12,000. Thickness, finish and site prep drive the price — use the calculator for your area.
Is stamped concrete worth the extra cost?
Stamped concrete costs about 2× plain but mimics stone, brick or pavers at a lower price than the real thing, and is a single poured surface with fewer weeds/settling issues than pavers. Good middle ground for looks vs budget.
Top cities in Tennessee
Metro-level concrete patio & driveway costs — usually a bit above the Tennessee state average.