Concrete Patio & Driveway Cost in Maryland (2026)
Concrete Patio & Driveway in Maryland runs about 10% above the national average. A typical 600 sq ft project starts around $3,960–$7,920 for standard broom finish. Estimate your exact project below.
Maryland runs above the national average on cost, reflecting a high cost of living and a competitive labor market in the Baltimore-Washington corridor.
Reviewed by the AnyCoster Research Team · How we estimate costs
Concrete Patio & Driveway Cost Calculator
Adjust the details for an installed-cost range tailored to you.
Length × width of the slab. A 2-car driveway is ~600 sq ft.
Ballpark estimate for planning — not a quote.
Get your exact price from local concrete pros
This is a ballpark — compare up to 3 free, no-obligation quotes from vetted contractors in Maryland.
Concrete Patio & Driveway cost in Maryland by material
Installed cost for a typical 600 sq ft project in Maryland.
| Material | Per sq ft | Typical MD project |
|---|---|---|
| Standard broom finish | $6.6–$13.2 | $3,960 – $7,920 |
| Stamped / colored | $13.2–$22.0 | $7,920 – $13,200 |
| Paver equivalent | $16.5–$30.8 | $9,900 – $18,480 |
What affects your Maryland cost
- Finish (plain vs stamped/colored)
- Slab thickness and rebar/mesh reinforcement
- Site prep, grading and old-slab removal
- Access for the concrete truck
- Local labor and material prices
Concrete Patio & Driveway in Maryland: local factors that move the price
Climate & weather
Humid summers, cold winters, and Chesapeake Bay and coastal exposure bring moisture, freeze-thaw, and occasional storm-surge concerns. Drainage and weatherproofing matter across the state.
Regional norms in Maryland
Brick and vinyl siding are common, with elevated or flood-aware construction near the bay and shore.
Best time to schedule
Spring and fall are the most comfortable seasons for exterior projects.
Permits & code
Most Maryland jurisdictions require permits for structural, roofing, and electrical work, with Critical Area and flood rules applying near the bay.
Maryland concrete patio & driveway — FAQ
How much does concrete patio & driveway cost in Maryland?
In Maryland, a typical 600 sq ft concrete patio & driveway project runs about $3,960–$7,920 for standard broom finish, installed. That's about 10% above the national average. Higher-end materials cost more — use the calculator above for your exact size and material.
How much does concrete patio & driveway cost per sq ft in Maryland?
In Maryland, installed concrete runs about $6.6–$30.8 per sq ft depending on material (standard broom finish $6.6–$13.2, stamped / colored $13.2–$22.0, paver equivalent $16.5–$30.8). That's about 10% above the national average.
Do I need a permit for concrete patio & driveway in Maryland?
Most Maryland jurisdictions require permits for structural, roofing, and electrical work, with Critical Area and flood rules applying near the bay. Always confirm requirements with your local building department, and factor permit time and inspections into your schedule.
When is the best time to do concrete patio & driveway in Maryland?
Spring and fall are the most comfortable seasons for exterior projects. Humid summers, cold winters, and Chesapeake Bay and coastal exposure bring moisture, freeze-thaw, and occasional storm-surge concerns. Drainage and weatherproofing matter across the state.
How much does a concrete driveway cost in 2026?
A standard ~600 sq ft concrete driveway runs about $3,600–$7,200 installed; stamped or colored concrete runs $7,200–$12,000. Thickness, finish and site prep drive the price — use the calculator for your area.
Is stamped concrete worth the extra cost?
Stamped concrete costs about 2× plain but mimics stone, brick or pavers at a lower price than the real thing, and is a single poured surface with fewer weeds/settling issues than pavers. Good middle ground for looks vs budget.
Top cities in Maryland
Metro-level concrete patio & driveway costs — usually a bit above the Maryland state average.